Hello there! What are the torque specs for the final drive fluid fill and drain plugs on the 2.5 liter? I saw one thread the drain was 25nm. Is this correct? Thank you! Also, my wife and I are headed to the UK next month and will be attending the Triumph Factory Tour. I cannot wait!
G’day All ! Firstly, thanks for all the help / advice / parts (Ishrub!) so far... Briefly, and pls delete if this info already here somewhere. Point me towards it tho first pls... What’s the best Torque/HP upgrade route? 2008 Classic, custom pipes, ram air, ozclaw, Mittzy rad tube, air box...
Hey guys, I need to remove the plastic piece around the right fork to use the SealMate fork cleaning tool in the hope to fix the effin leakage. Anything I should know before taking off all these screws, or anything I should pay attention to before starting to unscrew them? What is the torque...
Hi all my front rh caliper seems to be dragging , have checked the pistons and One has rust spots on it so have ordered a piston and seal kit off eBay , I was going to split the calliper to rebuild it but can’t find the torque settings for the 4 bolts that hold the calliper together , any clues...
Hello all. Great news, ive knocked out basically all the wiring/ tedious steps to swapping my rockets engine out. Was going to buy another torque wrench specifically for tightening everything up with no issues or hastles in NM or metric. Buuut now im pondering has the flip side to my wrench been...
I’m going to put on new dresser bars so I want to make sure it’s torqued correctly. In my book the only value I can find for this bolt is “See Note”. The problem is I don’t see the note... anywhere in the book. Does anyone know what the proper torque is?
"THERE IS NO REPLACEMENT FOR DISPLACEMENT" 2.5L (2472cc) Stroker Package Want a bigger engine and way more torque than the new Rocket 3? Add 10% BHP and 12.5% Ft Lbs to your engine, throughout the entire RPM range. No trade-offs! Premium performance parts, all manufactured in the USA and...
Wondered what others observed on this subject. My honda vtx 1800, when you accelerate, it would throw you back as it propelled you forward. On this rocket, no throwing back, just forward. Have you noticed this, and if so what is the explaination? Is it 2 cylinder vs 3? Thanks in advance!
I just finished a Neville Lush piston and cam rebuild in ""record time"" with no prior experience. I had allowed myself a full five days during the Christmas holidays for the install. Well, now, more than three months later, I’m finally in a position to say, "job completed!" and share this story...
Installed the Ramiar some time ago and had the Jardine set up from new. Downloaded and installed a Tune From @HansO and was wondering how it was doing. Always ran great. Last weekend was in a long Ride and it starting acting up. Would stall under decel when coming to a stop and act as if hydro...
how about that just found out this morning as I am getting a new rear tire on the back wheel..exedra max naturally my manual show torque in NM so I translated the NM in foot/lbs and found out my rocket has 268.45 newton/meters of torque . so when my eyeballs go flat that's close to...
Reinstalling rear wheel speed sensor disc. Had red loctite on it. Anyone know the torque setting on these little bolts? Also, torque for final drive flange ("driven flange" in the manual - the gear on wheel that mounts to hub). Blue loctite there.... I couldn't find anything in a search Many...
Wondering how to achieve smoother lower end torque, I'm lazy at times and don't want to necesarily down shift in slow moving areas of road. My set up is pretty basic currently, Ram Air, Dave Platt link pipe and stock mufflers. I have tried the TORs but the drone kills my ears even with ear...
So, I'm still building out my R3T exactly how I want it, and seeking a bit more performance. Right now, I upgraded to a Dain 3-to-1 slip-on, PCV (no dyno tuners using TuneECU), and a RamAir kit. Right now I dyno'd 145hp, 151ft/lbs, not bad considering it's at the wheel and minimal upgrades, but...
Mounting the 50mm crash bars, need the torque setting for the large bolt that is on top of the engine, don't know what it's called. 10 inches long or so, goes from one side of the engine to the other, when I look it up in the manuel it says 'see text' can't find it in text. Thanks Hoopla
Is it possible to remove the back torque limiter without removing the engine from the frame because i have what appears to be a lot of backlash in my transmission. sounds like metallic knocking on open and shutting throttle.
Finally got my date with the dyno . Restrictions removed , secondarys opened 100% and fueling sorted . First gear is now crisp and sharp off the throttle with wheelspin and second is long and powerful . The bike now pulls like an express train up to the increased limiter with no more clattering...
Opinions are welcome on this thread, but it must be your own. Do not attempt to legitimize your opinion via some other writing, law, teaching, similar event, or source of information.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register. By continuing to use this site, you are consenting to our use of cookies.