I'm feeling a bit of clutch slip shifting from 4 to 5th mostly. Or really only. And only when really getting on it. Anybody else? I'm going to change the oil. See what happens. 6.5k miles, so seems about time. I don't like stretching it out to the manufacturers suggested mileage. I always...
i have been thinking about this for several days about the consequence of what would happen if i put this info out there and someone dropped there bike and got hurt. i decided the info should be there for those that want it.
for early models. you find the black/orange wire from clutch switch...
Im finally finishing up on a 2nd gear upgrade due to Transmission issue.
I noticed when attaching the clutch cable to Clutch lifter arm that the position doesn't match the rotation point when I originally took it apart in 2021.. First picture is original position .
2nd is as it is now. Cable has...
Has anyone done a clutch replacement on our bikes? If so where are the clutch discs and everything located and how do they come apart? I have a 2020 r. I’ve done clutch replacements on past bikes like my old r1 and old cbr1000rr but not sure if it’s anything similar on these bikes. Thanks!
Clutch fluid leaking somewhere.
This is my first bike with a hydrolic clutch. Thought it felt odd when I first road it, but was assured that's how they feel. Bought it with 9k miles on it from an individual. A few days later I realized there's an eye glass on the fluid and the fluid was below...
After a winter check up on my engine and new clutch fitted I had a complete facelift and redesign of the Chariot by Lumley Engineering including lowering the diff ratio. Got the Chariot back in time for the lovely weather in April and took it out for a run. The clutch lifter failed within 50...
Was watching an early YouTube video about the 2.5l Rocket. The bloke in the video described the clutch as “lady fingers” suggesting a light action. I’ve never found mine to be that way. In fact, during a long stop-start ride through Edinburgh today on my 2021 R3R, I was thinking that the...
Evenin all
I'm just finishing putting this motor back together all parts were boxed separately I'm left wandering as looking at the manual I seem to be missing a spacer no 27?? Which looks like it's supposed to back the wavy one up? parts were replaced a while back and I remember scratching my...
Quick recap - my clutch does not fully disengage once the bike warms up. Cold, everything works the way it should. Warm, I can not go into neutral from first, and if I rev it a little with the clutch handle pulled in it will try to take off. I have had the lifter arm replaced (it was...
Hi Folks
Approximately 6 months ago i parked up my 2006 Rocket 3 in the garage to do couple of things to it including painting the tank and fenders and also changing the handle bars. Long story short, after changing out the handles bars I realised I needed a different length clutch cable. So I...
Good day eh! Looking for help , trying to find some parts and hopeing someone can give me ideas and help figureing out my problem.
I have a very distinct noise when decelerating. It is difficult to explain the noise. Its not a grinding noise, not chattering, but more of a low pitch growling noise.
Just bought a used 2022 GT with 23K miles and changing the fluids. Done the brakes and now wanting to flush the clutch circuit. Trying to locate the slave without taking it apart.
Manual is no help and did a search on YouTube and the forum without success. Probably not trying hard enough.
Could...
Hi all
Had the pleasure of my clutch packing up, nothing at the lever ,managed to get a friend with a car trailer to get me home Mine has the TTS hydraulic conversion and this is what i found on dismantling ,O rings shot and damage marks on the Oberon slave ,
Phoned Oberon ordered a new unit...
Hello guys,
I feel like my clutch lever needs to travel all the way before the clutch gets in contact. Is that normal? Is there a way to reduce that travel? Adjusting the lever maybe?
Thanks for your help in advance,
Despite lowering the overall gearing by fitting 245 x40x17 instead of 245x45x17 I have still not got rid of my clutch slip problem. Has anyone fitted an extra driven plate in the clutch pack?
I have a 2006 Rocket 3 Classic. The clutch works fine on cold start, then when it gets warm - in a minute or two - will progressively fail. Stalls, I have to put it in neutral to re-start it, and it grinds if you try to downshift into first. Let it sit and cool and you will get another minute...
Good day group. In the preparation of getting my R3T ready for her inspection next Monday (March 18), one of the things I did was (with the help of another member "SENSFAN" , I installed a set of stock silencers. Now that I can "hear" more things one thing I noticed was a bit of clutch "chatter"...
Put a new detent spring, barnett clutch, and barnett red springs into my 2011 triumph rocket 3. Now attempting to get the clutch set right and it is not disengaging. I tried the 3mm of free play and it wouldn't start, jacked the bike up and the rear tire started spinning when it turned over any...