2015 Roadster map with TORs.

[Wajhi]

Wonder if that is some crap that CA required as the cats are inside the big cans on the stock 2010-2018 Roadsters(are you sure about the year of your bike?)
F Phil(that did not come out good) if all you have done is install the TORs then your next step HAS to be the intake system, do a search for air filters and you will see what most of us are using.

So I slipped the TORS on the stock place....applied the sealant....started the bike....after few minutes saw fumes coming from the joints where I applied the sealant....turned the bike off to let it dry.....is it normal or do I have to open them again and apply the sealant again? Cos the sealant packing days let it dry for an hour and then let it stand for 24 hrs????

 

[EwoutR3]

Some fumes are oke, just check the seals with the engine running when it dried. You should not feel exhaust gas with your hand close to them. You can also use a piece of toiletpaper and hold that near the seals. The toiletpaper should not be fluttering.

 

[scot in exile]

Some fumes are oke, just check the seals with the engine running when it dried. You should not feel exhaust gas with your hand close to them. You can also use a piece of toiletpaper and hold that near the seals. The toiletpaper should not be fluttering.

Toilet paper is worth more than gold at the moment, I suggest you use a $100 note instead

 

[tribal]

So if you guys only have TORs on 2015 Rocket III's why not use this map in the Resources section above?

OEM_TOR_Tune_20776 2018-06-01 "TOR exhaust file for late model Roadsters 2014+ "

Or, if you add Ram Air or K&N's (not sure why you wouldn't because just doing the TORs is like putting a larger barrel on a gun and using the same bullets) try this one:

R3R_Slip_grafted_onto_20773_base.hex by Sir Claviger located in the TuneECU Custom Map page.

 

[Kojack1970]

So if you guys only have TORs on 2015 Rocket III's why not use this map in the Resources section above?

OEM_TOR_Tune_20776 2018-06-01 "TOR exhaust file for late model Roadsters 2014+ "

Or, if you add Ram Air or K&N's (not sure why you wouldn't because just doing the TORs is like putting a larger barrel on a gun and using the same bullets) try this one:

R3R_Slip_grafted_onto_20773_base.hex by Sir Claviger located in the TuneECU Custom Map page.

Agree with Tribal, get the ramair. Just doing either the TORs or just the ramair has minimal impact, but both together is where you will see a difference.

 

[CrzystghndKC]

So while we're talking tunes I have installed Paul Bryant crossover, TORS, and Ramair. Loaded tune 20355 off resources. After reading this I am a little confused about the O2 sensor. Would this be disabled? I really didn't check that and if it is disabled do I remove it? Also in this tune it says you must adjust the TPS and ISCV. Well I rode it before doing that and I think it's running GREAT. So should I adjust them or walk away. I am the best at opening a can of worms so I try to leave well enough alone.

 

[Kojack1970]

So while we're talking tunes I have installed Paul Bryant crossover, TORS, and Ramair. Loaded tune 20355 off resources. After reading this I am a little confused about the O2 sensor. Would this be disabled? I really didn't check that and if it is disabled do I remove it? Also in this tune it says you must adjust the TPS and ISCV. Well I rode it before doing that and I think it's running GREAT. So should I adjust them or walk away. I am the best at opening a can of worms so I try to leave well enough alone.

My understanding is that if the tune does not have the O2 sensor disabled, it will eventually write over the fuel table, if I remember correctly. The HANSO tune I used for my Roadster has the O2 sensor disabled, so I physically removed it and plugged the hole.

 

[ArekDeBoss]

I know absolutely nothing about maps TORs filters etc. I have 2015 standard roadster with what I think is David Platt short exhausts. And since recently i had to but Tunecu cable and pay for an app I would like to get and load some maps to improve performance. What would you suggest?
Thanks

 

[Kojack1970]

I know absolutely nothing about maps TORs filters etc. I have 2015 standard roadster with what I think is David Platt short exhausts. And since recently i had to but Tunecu cable and pay for an app I would like to get and load some maps to improve performance. What would you suggest?
Thanks

I have a 2016 Roadster with Ramair, DP cross over, DP mufflers (not shorts) and used the HansO tune (below) from the resources on this site. Works well for me. I want to get it on Dyno this summer.

Hans0 tune for 2014+ Roadster, TORs, triple/Ramair filters, ect. 2018-06-01

 

[ArekDeBoss]

I have a 2016 Roadster with Ramair, DP cross over, DP mufflers (not shorts) and used the HansO tune (below) from the resources on this site. Works well for me. I want to get it on Dyno this summer.

Hans0 tune for 2014+ Roadster, TORs, triple/Ramair filters, ect. 2018-06-01

And how to do that? Technically i mean. Just load from here to tunecu app then what?
Sorry to be a nuisance