Search results for query: *

  1. lunatic

    C-Clip failure...trashed transmission.

    I'm kind of surprised someone hasn't sued triumph from getting injured because of their defective transmissions.
  2. lunatic

    Robinson Industries Transmissions

    Has anyone used Robison Transmission lately? I have tried contacting them for transmission work. I'm not getting a reply. First email I sent was on June 29th. I was asking a technical question about a transmission he had done for a previous customer, just wanted to make sure bout something...
  3. lunatic

    C-Clip failure...trashed transmission.

    Finally getting around to fixing my bike that exploded the transmission last fall. I was at WOT when it grenaded itself in third gear just when I shifted into 4th @ 6500rpms. Made a loud explosion then loud grinding noises when I was trying to slow down, the rear tire locked up when I got back...
  4. lunatic

    Tuning turbo with PCV problems

    I removed the stock o2 sensor and unchecked the box in TuneECU. I am using the wideband o2 that came with the autotune. From my experience with the auto tune, it seems slow to adjust and has a hard time with pressure base tunning. It also wont make adjustments its below 10.00 or above 15 afr...
  5. lunatic

    Tuning turbo with PCV problems

    Here is another video of it acting up....Im not sure what going on with it. I will run fine for about 20 minutes then start doing this. It will die and not start unless I cycle the ignition switch. I have checked all the wires and didn't find anything.
  6. lunatic

    Tuning turbo with PCV problems

    I was thinking the same thing before I asked. I am not sure what the stock map sensor is. I would guess its a 1 bar? That's why I didn't run a hose to it. I just have it seeing atmospheric pressure and put all the switch points on the f-l table on 0. I'm not even sure if that's the correct...
  7. lunatic

    Tuning turbo with PCV problems

    I wired the 3 bar bosch map sensor into same power source as the stock map sensor but only the power source. The 5 volt signal coming from the 3 bar is feed into the pcv only. The only advantage I see with the bosch is it capable of higher boost levels. If I had known the stock map sensor would...
  8. lunatic

    Tuning turbo with PCV problems

    Here is how I have it setup for tuning, maybe this is why I am having issues with the autotune at idle and low throttle pos. The stock map sensor wires are plugged in but the vacuum lines are not connected to it. I left the wires connected as not to throw a check engine light. I have all the...
  9. lunatic

    Tuning turbo with PCV problems

    How many of you have done pressure based tuning? I am having issues with the pcv ignition module. Is there any other software or ways of tuning via pressure base besides Dynojet? I am not impressed with the them. The auto-tune is slow, I can do better with data logging and manually putting in...
  10. lunatic

    Turbo size :updated, turbo installed now.

    Im using a combination of tune-ecu and PCV with pressure based fuel and timing. Just recently purchased a power commander pod 300 that has data logging. Not sure when I'll make it to a dyno with the all the shut downs. For now I'm going to tune it myself with the auto-tune and the pod 300.
  11. lunatic

    Turbo size :updated, turbo installed now.

    I went with bigger injectors. I have plans of a larger intake, 3" down pipe, meth injection and back cut gears after this ridding season is over.. I'm kinda worried the transmission will go out if I do the improvements listed. For now I'm going to ride it as is till next fall, then tear into it...
  12. lunatic

    Turbo size :updated, turbo installed now.

    Finally finished it up this weekend. Been a long winter project. Here are some pictures, wish I would have taken more.
  13. lunatic

    Some Rockets like too

    Got to slip the clutch alot more. The rocket is hard to launch especially if you have modded it any. With 200hp, there is no way you can go wide open throttle if it hooks. At any speed in first it will wheelie up. I would almost guess the carpenter bike leaves in 2nd gear?
  14. lunatic

    Pcv and Tunecu with 3 bar map

    How are you guys installing a 3 bar map sensor for Pcv and Tunecu for boost applications? I read this post from a while back. It explains how to setup a 1 bar map for pressure base tuning. but not much about 3 bar. How To: Add Pressure Input for PC-V
  15. lunatic

    Carpenter Racing Turbo Rocket

    What was this motor in? Not sure how that would work in a rocket frame? Is this configuration for the streamliner?
  16. lunatic

    Turbo size :updated, turbo installed now.

    To answer my own question. I got in contact with BSA Bob who has done a few turbo rockets. I have the stock turbo from a GMC Syclone. When I upgraded the turbo on it, I kept the stock turbo. Its has been under my bench for years waiting for something.. Now its going on my bike! Mitsubishi...
  17. lunatic

    Turbo size :updated, turbo installed now.

    What size turbo are we using on our bikes?I read a couple post on here, there is some good info. I didnt find what turbo size we are using.
  18. lunatic

    What a state new rocket ?

    I agree with you, I prefer the older model too.
  19. lunatic

    Rocket market

    Actually mine gets better mileage after modifications. Stock mine was 38-40 mpg. With mods and tune, now 42-44 mpg. But I do need to put in 91 premium. :D
  20. lunatic

    Rocket market

    I only looked at craigslist, but one of them is a 2013 touring in Omaha with only 4100 miles on it. 2013 Triumph Rocker III, Touring
Back
Top