Cable not showing when connected to computer

[GaryA]

I have started, downloaded and installed TuneECU.
Now the cable, downloaded and saved drivers, disconnected the internet, plugged in the cable but no dialog boxes cam up.

Should something have shown on the computer saying I had connected something and where are the drivers?

Its Windows 10 as well.

Any ideas on what has gone wrong?

 

[Mittzy]

Does the PC make a sound?
If it is a Lonlec cable it would have instructions for setup

 

[warp9.9]

That would be a dedonk sound when you plug the cable in to the computer whether its hooked up to the bike or not

 

[GaryA]

Okay, no sound, but I usually have the sound turned down.
It is a lonlec cable, ordered in from the UK if I remember correctly.
I'll have another play this evening and chase these things up.

 

[Steel]

Watching with interst. Since I've upgraded my laptop to Windows 10, my Lonlec cable hasn't wanted to connect either.

 

[WyldCFH]

Go here >>> D2XX Direct Drivers
Click this, in red oval

Install the program you just downloaded

Connect cable to computer
Hit Windows and X key at same time
Click Device Manager
Double click Ports (COM & LPT)
Double click USB Serial Port (COMx) x can be any number, depends on the number of COM ports you have used
Click Driver tab
Check Driver Version is same as you installed

Open Tune ECU
Click Options
Click Interface
Click USB
Click FT232R USB UART This should put a checkmark before FT232R


AFTER all of that, connect to bike

 

[GaryA]

Go here >>> D2XX Direct Drivers
Click this, in red oval

Install the program you just downloaded

Connect cable to computer
Hit Windows and X key at same time
Click Device Manager
Double click Ports (COM & LPT)
Double click USB Serial Port (COMx) x can be any number, depends on the number of COM ports you have used
Click Driver tab
Check Driver Version is same as you installed

Open Tune ECU
Click Options
Click Interface
Click USB
Click FT232R USB UART This should put a checkmark before FT232R


AFTER all of that, connect to bike

Ah ha, now that is instructions!

Thank you WyldCHH, I will do that and let every one know.

 

[sleeves]

Go here >>> D2XX Direct Drivers
Click this, in red oval

Install the program you just downloaded

Connect cable to computer
Hit Windows and X key at same time
Click Device Manager
Double click Ports (COM & LPT)
Double click USB Serial Port (COMx) x can be any number, depends on the number of COM ports you have used
Click Driver tab
Check Driver Version is same as you installed

Open Tune ECU
Click Options
Click Interface
Click USB
Click FT232R USB UART This should put a checkmark before FT232R


AFTER all of that, connect to bike

As Wild says.

Win10 has forced driver assigning so if you simply plug in the cable windows assigns it a driver (the wrong one) you need to install the drivers for the cable and it will work. Frustrating but they are trying to make things simple for the masses.

 

[GaryA]

Thank you all, I think the cable and driver is now working.
Next is to try connecting it all up and giving the HansO tune a go.

 

[Mrbuickstage1]

Watching with interst. Since I've upgraded my laptop to Windows 10, my Lonlec cable hasn't wanted to connect either.

I’ve tried yesterday to hook up tuneecu I may have lost my original tune not sure can’t connect I have a dong sound with the Wright cable , I’m using windows 7 can’t seem to connect to ecu I have a 2007 r3 classic, delete cat and Dain slip on pipe ? Idk trying again today bike runs but Im Afraid she’s lean
Oh ya had a dealer install fog lamps now they won’t come on power to relay and switch side works I can power load side of relay and make lamps work is there anything lease for power side of relay switch since it gets power from wiring harness