Switched wire to tap into

dd14x

.040 Over
Joined
Aug 4, 2024
Messages
95
Location
Texas/USA
Hello, I'm looking to wire up a pair of amber running lights on my 2025 Rocket 3 GT - I plan to use the innovv power hub to provide power to the light only when ignition is on.
This power hub is wired to the battery directly, but has a trigger wire that signals whether the ignition is on or not

On my prior motorcycle (Harley), I tapped into the rear tail light (which was on only when ignition was on) - the power hub also delays power output for 10 seconds after ignition is on (to prevent overload).

On the Rocket 3, is there a wire under the seat that can be tapped into for this?
 
I have a healtech, but used the acc. switch to bypass auto off. I found this plug and tapped into it to avoid cutting into any wires. It's on the left side, hidden along the edge. Probably plug for Bluetooth? 🤔 Anyways, it's just capped off on mine. Just de-pin the acc wire, and plug your wire in to get acc power
 

Attachments

  • 20241111_101311.jpg
    20241111_101311.jpg
    240.9 KB · Views: 58
  • 20250330_183754.jpg
    20250330_183754.jpg
    266.3 KB · Views: 57
  • 20250330_183801.jpg
    20250330_183801.jpg
    239.4 KB · Views: 62
I have a healtech, but used the acc. switch to bypass auto off. I found this plug and tapped into it to avoid cutting into any wires. It's on the left side, hidden along the edge. Probably plug for Bluetooth? 🤔 Anyways, it's just capped off on mine. Just de-pin the acc wire, and plug your wire in to get acc power
Thank you! The pictures are very helpful
 
I have a healtech, but used the acc. switch to bypass auto off. I found this plug and tapped into it to avoid cutting into any wires. It's on the left side, hidden along the edge. Probably plug for Bluetooth? 🤔 Anyways, it's just capped off on mine. Just de-pin the acc wire, and plug your wire in to get acc power
So to be sure: the black&white is switched )on with ignition on, off with ignition off). Excuse if it's obvious but mechanical all's good here, it's the electric stuff where I'm a nOOb.
 
There is a wire on the left side under the seat that runs to the tail light that I used a Posi-Tap on for my front and back "dash" cams, just FYI, but if I'd known about this switch I'd have gone that route. Thanks for sharing- I need to make a note of that post for future reference.
 
There is a wire on the left side under the seat that runs to the tail light that I used a Posi-Tap on for my front and back "dash" cams, just FYI, but if I'd known about this switch I'd have gone that route. Thanks for sharing- I need to make a note of that post for future reference.
Color of the wire? It for my camera set-up too (Innovv K6). I will post some results here in due course. First I need to get the bike here. I might go for a Health Thunderbox so that I can also charge my phone (will be using an SP-Connect charger) and perhaps some other stuff.
 
I have a healtech, but used the acc. switch to bypass auto off. I found this plug and tapped into it to avoid cutting into any wires. It's on the left side, hidden along the edge. Probably plug for Bluetooth? 🤔 Anyways, it's just capped off on mine. Just de-pin the acc wire, and plug your wire in to get acc power
I also used this connector (under your left butt cheek) to provide an ignition on indication to my Chigee carplay screen. I have no intention of ever getting the bluetooth adaptor so I just clipped the switched 12V wire that I found off the back of the connector and spliced to it. Works great.
 
Hello, I'm looking to wire up a pair of amber running lights on my 2025 Rocket 3 GT - I plan to use the innovv power hub to provide power to the light only when ignition is on.
This power hub is wired to the battery directly, but has a trigger wire that signals whether the ignition is on or not

On my prior motorcycle (Harley), I tapped into the rear tail light (which was on only when ignition was on) - the power hub also delays power output for 10 seconds after ignition is on (to prevent overload).

On the Rocket 3, is there a wire under the seat that can be tapped into for this?
i have said numerious times before in other posts,

Aftermarket bridging with rear tail light is not possible as brake/tail light is controller by ABS module and there is no mechanical switch which is causing break light to work on 2.5L
you will probably see an error on dash / instrument as soon you *tap* anything into any light
no company has so far made it work for 2.5L rocket with rear tail light/break light OR LED strip sequential blinkers.
 
Back
Top