Recent content by headster

  1. 2014 Roadster - removing stripes

    they are vinyl stripes under the clear coat, you will have to sand the clear down and then remove the vinyl and base coat it black and clear it again.

  2. 4 inch speakers plus amp

    Those are nice. I used to make my own sets that I sold to the Valkyrie crowd, just remember that whatever they state for wattage is BS, the size of the amp and the internals is good for roughly 38W RMS per channel, after that you would need a much larger amp with inverters build in to get...

  3. front turn signal wires

    there are 2 sets of white connectors on the main wire loom front left under the tank that then runs inside the loom until it comes out at the connectors by the ECU, right side panel. Inside the loom they splice into wiring for the idiot light, turn signal switch and flasher unit. you can cut...

  4. people keep refering to the R3T having smaller...

    The reason I post this is that when I first got the Touring I could only find the part number different and when I posted about it everyone jumped on the different part number it must be smaller band wagon. After finally getting them off the bikes I can tell you that other than the plates...

  5. people keep refering to the R3T having smaller...

    Throttle Bodies So I pulled both bike's throttle bodies off since I am cleaning both bikes. 05 Standard Rocket 3 part number stamped on each = 1245000-SEP Inside measurement top = 55.88mm Inside measurement bottom = 55.88mm 08 Touring Rocket 3 part number stamped on each = 145100-VH6...

  6. Whats the best way to clean brake dust and pitting

    I took mine off when I got the bike and wet sanded them and polished them. Now the dust just rinse off and no pitting due to nothing to stick too.

  7. trunk

    I do not know that brand trunk but the wiring for the brake/running lights and the turn signals all connect from the rear fender to the main wiring loom under the right side panel just above the ECU, if that helps

  8. Electrical help

    really easy to hotwire a R3, as long as you have a 8mm and 10mm wrench to remove the left sidecover, if you are on a R3T it is even faster. I was able to start the R3T in under 15 seconds, if the wheel is not locked then your bike will be gone in 16 seconds. The R3 took me just under 2...

  9. MORE POWER AT 3/4 THROTTLE?

    remove the secondaries and try it again... Mine was hesitant too, even with the 100% tune and once I got rid off them she seems to be running hard all the way through WOT

  10. Whats the best way to clean brake dust and pitting

    Don't brake...

  11. Low cost RFID tag reader to enable/disable ignition

    You don't need the key in the ignition, if you forgot the remote then you use the key as you always would. If the key is in the on position in the ignition then everything is on, it over rides the remote, if it is in the off position then you can turn the bike on/off with the remote.

  12. Low cost RFID tag reader to enable/disable ignition

    I have 2 setups and it is keyed, I can not get one bike started with the other bike's remote, even after I reset them they still only work on the receiver that came with it. I can usually walk out of a joint and once I spot my bike I hit the button and put it away, have my helmet on and mount...

  13. Low cost RFID tag reader to enable/disable ignition

    I posted a wireless solution on the How to Goldmine for about $45.00 and I have it on both my Rockets, works great

  14. Diff and housing

    I bought one off ebay with 8k miles for $289.00, look at...

  15. quick release sissybar

    It is a separate box and they should have ordered it for you, mine came with the kit and it is free, they just need to order it since there is a part number tied to it.
See more
Back
Top