Electric question

[ArekDeBoss]

I can not locate relay for indicators.
I have located few but they seem way too small. Please see a picture.
I can not find in a manual a location for indicators relay anywhere.
Can somebody help?
It's for sequential LED indicators which even with resistors flash normal frequency but only half way through.
When connected directly to the battery they flash fine. When connected to old indicators plugs they don't. Not at all until added resistors. Then after that only half a way. So I need to locate a relay.
Help please
Forgot to mention it's 2021 GT rocket

 

[imcool]

I can not locate relay for indicators.
I have located few but they seem way too small. Please see a picture.
I can not find in a manual a location for indicators relay anywhere.
Can somebody help?
It's for sequential LED indicators which even with resistors flash normal frequency but only half way through.
When connected directly to the battery they flash fine. When connected to old indicators plugs they don't. Not at all until added resistors. Then after that only half a way. So I need to locate a relay.
Help please
Forgot to mention it's 2021 GT rocket

There is NO relay in this bike for blinkers.
There is also NO any light switch for brake lights, no where on brake lever or elsewhere.

The BINLKING SIGNAL is sent by instrument/dash.
Brake lights are also controlled by instrument/dash+ ABS module ECU.

So far no person has been able to install sequential indicators, hope you become the first one.

Good luck

 

[ArekDeBoss]

There is NO relay in this bike for blinkers.
There is also NO any light switch for brake lights, no where on brake lever or elsewhere.

The BINLKING SIGNAL is sent by instrument/dash.
Brake lights are also controlled by instrument/dash.

So far no person has been able to install sequential indicators, hope you become the first one.

Good luck

Are you being serious? All this digging and disassembling for nothing?

 

[Kevin frazier]

Never give up, how about in line diode like we have to do on touring.

 

[ArekDeBoss]

Never give up, how about in line diode like we have to do on touring.

That is way to complicated. I can fix your dog not do wiring for lights . No chance

 

[imcool]

Are you being serious? All this digging and disassembling for nothing?

you should have looked at manual>electric circuit diagrams> rear light +turn indicators before started opening things, yes, I am serious.

 

[imcool]

Never give up, how about in line diode like we have to do on touring.

Somethings are meant to give up, CAN BUS in encrypted so even professional companies are unable to add extra rear brake lights to this bike. Same goes for sequential blinkers, even ABS bleed is not possible with tuneeecu and 'dealertookUK' aftermarket software, I bought both and asked them why ABS bleed does not work and they said 'sorry'. I have emails from them.

I am waiting, looking here and there on FB etc, maybe someday someone will figure this canbus stuff.

Turn signal help

Hello all! So I'm posting up to see if anyone has any ideas or experience with my problem. I installed aftermarket led turn signals while moving my plate. The turn signals at first switch will run normal for 3 or 4 cycles. Then it will just shut off the rear signal lights and pop up an error...

www.r3owners.net

 

[ArekDeBoss]

you should have looked at manual>electric circuit diagrams> rear light +turn indicators before started opening things, yes, I am serious.

Well as I said its all too complicated for me. My brain in wired differently ;-(

 

[Jay]

Are you being serious? All this digging and disassembling for nothing?

At least you got to see the guts…Triumph does make a set of scrolling indicators for the bike and I understand they have to be activated in teh software by the dealer before they will work properly. You might just need a software udpate. I had a similar thing on my Zero EV motorcycle when going from regular incandescent bulbs to the LED. The dealer just flipped a bit in the software to account for the resistance change so the computer knew the lights were working as normal.

 

[ArekDeBoss]

At least you got to see the guts…Triumph does make a set of scrolling indicators for the bike and I understand they have to be activated in teh software by the dealer before they will work properly. You might just need a software udpate. I had a similar thing on my Zero EV motorcycle when going from regular incandescent bulbs to the LED. The dealer just flipped a bit in the software to account for the resistance change so the computer knew the lights were working as normal.

Will call them to ask