Recent content by Zanx

  1. Zanx

    Lights, dash but no spinny spinny.

    Ok, next step, voltage check on fuses. 1 13.26v 2 13.03v 3 13.03v 4 12.9v 5 12.19v (this one if from the ignition switch) 6 13.16v (to EMR) 7 13.16v (fan) 8 11.96v (ACC) 9 12.5v (from ignition) 10 12.3v Main fuse 13.07. Some pretty ****ty variances there, ideas?
  2. Zanx

    Lights, dash but no spinny spinny.

    Thanks Turbo, that's some solid info. Tuneecu still isn't connecting so I guess the ECU isn't powering up. Clutch and side stand switches are next in line for examination. I have a neutral light, I did try with the stand up and the clutch in. All the relays (two on the right and 4 on the...
  3. Zanx

    Lights, dash but no spinny spinny.

    Next question is, where are the grounding points? I know there's one on the starter, one on the battery, any more? Might just make my own.
  4. Zanx

    Lights, dash but no spinny spinny.

    Jammed a wire in the supposed earth terminal of the starter relay and ran it to the neg on the battery, and now we have the starter working and it smells like fuel making it's way through. Getting there, just need sparks.
  5. Zanx

    Lights, dash but no spinny spinny.

    Next stop, engine management relay supply, this is fed by the ignition switch via the fuse 2 (in) and 6, (out). This should point the finger at the switch if there's no current heading to the relay.
  6. Zanx

    Lights, dash but no spinny spinny.

    Thanks, I'll bear that in mind for the next investigation. I took the relay home to test and it appears to be fine, power across 85 and 86 triggers the relay and creates continuity between 30 and 87, releasing the power from 85 and 86 breaks continuity between 30 and the middle pin out (87a)...
  7. Zanx

    Lights, dash but no spinny spinny.

    I'll keep this going till it's fixed. Latest is that the voltage to the starter relay is good, the voltage to the relay terminal that is connected to the starter button is good when the button is pressed. Surely this leaves the relay as a main suspect? I'll be resting relay tonight. Oddly I...
  8. Zanx

    Lights, dash but no spinny spinny.

    Might just use a battery isolator switch with a red key.
  9. Zanx

    Lights, dash but no spinny spinny.

    Plugged the meter into fuse 9 and wiggled the key, settled on 5.5v till I waggled the key a bit, then it dropped to 4. something. Dunno, maybe I will try and jump it off my Noco next week and see how we go. The lights don't look like they are getting 6v, too bright.
  10. Zanx

    Lights, dash but no spinny spinny.

    Right, checked voltages across all the active fuse terminals and all 12.4 to 12.6v except the headlight fuse, that's showing 6v. This isn't right, right? Horn, brake light, indicators all working, Tuneecu still not interested in connecting, getting as far as flashing yellow bar. So fuse 9...
  11. Zanx

    Lights, dash but no spinny spinny.

    Ok, all fuses check out fine on the meter. Tuneecu seemed to be hunting for Bluetooth devices yesterday, I'll try again today with the BT off on the phone.
  12. Zanx

    Lights, dash but no spinny spinny.

    Hi, yes gauges sweep, lights on gauges all on. I have visually checked all the fuses but will run a meter over them tomorrow. Rear sidelight works, didn't check the brake or horn, again I'll do this tomorrow. I did put the light fuse back in. Thank you by the way, as long as I didn't fry the...
  13. Zanx

    Lights, dash but no spinny spinny.

    I'll throw myself at you collective mecies and see what happens. I got the 2004 ready for a map upgrade today but I pulled the wrong fuse, it wasn't the light fuse, it seemed to power the OBD cable because the light went out. Amyhoo. found the right fuse, connected to Tuneecu on my phone just...
  14. Zanx

    Unable to read map, cable driver timing out.

    Desparately trying to read my map so I can get the idle up from a ridiculous (stalling frequently) 600rpm, but I only get 80% through reading the map (20226) when the popup on the phone asks if i want to connect to the cable and it all goes tits up. Tuneecu doesn't seem to have 20226 in the...
  15. Zanx

    Pre loved Dave Platt Slash Short bolts and stuff.

    Bought a very nice Dave Platt shorty slash (used) for my 04, lovely bit of kit I must say, however, it didn't come with the bolt, can I ask if there;s anything special about the right hand bolt (header side)? I only ask because it doesn't seem that stable with a regular replacement bolt and it...
See more
Back
Top