Search results for query: *

  1. RIII Forever

    Stepper motor regulation problems

    thank you so much for all the support! 🙏
  2. RIII Forever

    Stepper motor regulation problems

    thank you very much everyone! I'm really happy that the bike is perfect again after some time!
  3. RIII Forever

    Stepper motor regulation problems

    Thanks guys, all solved! My problem was that the accelerator throttle didn't reset to the starting point! And so this staggered the distance then with the stepper motor! I leave the photos here to understand each other better as I don't know English well and I'm using a translator. Well...
  4. RIII Forever

    Stepper motor regulation problems

    should this be the time to measure 0.5? this morning I saw that when I press the reset for the first time and the stepper motor retracts, there is space! Ok Tomorrow i adjust ti 0,62 The primary tps!
  5. RIII Forever

    Stepper motor regulation problems

    thanks a lot for the help, tomorrow I'll try to screw the nut and redo the adjustment! My rocket is from 2016 Yes, throttle plates are closed!
  6. RIII Forever

    Stepper motor regulation problems

    yes yes I'm using Tuneecu! this happens to me: ISCV reset start - I wait for the stepper motor to close completely and septum 0.60 - I double click, the motor swings between 0.60 and 0.68, I try to adjust it using the screw on the stepper motor but I can't get it to go to 0.72 as the thread...
  7. RIII Forever

    Stepper motor regulation problems

    Thanks warp9.9, here maybe the problem is here, with the engine and ignition off, my accelerator goes against the stepper motor and the 0.5 mm thickness gauge does not pass, not even the 0.25mm one! to install the stepper motor at 0.5 do I have to do it with the engine and ignition off with the...
  8. RIII Forever

    Stepper motor regulation problems

    thank you very much Herman, however for the adjustment of the thickness 0.5 mm how do you do it?
  9. RIII Forever

    Stepper motor regulation problems

    Hello everyone, I have a problem with the idle on cold start, the bike is at about 1300 rpm and I basically have to pull the idle butterfly back by hand near the stepper motor to get it regularized, otherwise it takes several minutes to get regular. I cleaned the primary TPS sensor (blue...
  10. RIII Forever

    Idle is over 2700 rpm Help

    ok then it should change easily! Thanks for sharing your experience
  11. RIII Forever

    Idle is over 2700 rpm Help

  12. RIII Forever

    Idle is over 2700 rpm Help

    Hi then I followed this video Where practically it shows that without disconnecting the stepper motor it makes the adjustment of both the primary tps and the stepper motor. You instead in addition to measuring 0.5 mm do this (correct me if I misunderstood): - Ignezione off disconnect the...
  13. RIII Forever

    Remove stock fuel limiter

    perfect we hope! p.s. compliments for wheelie Rocket in your image
  14. RIII Forever

    Remove stock fuel limiter

    ok thank you very much we are waiting, I don't have the whole 240 hp kit ..... if @R-III-R Turbo has maps for only the exhaust and filter it would be excellent!
  15. RIII Forever

    Idle is over 2700 rpm Help

    @Speedy thanks for the reply, sorry for the delay I did a little test, but not to change the minimum and I performed the ISCV reset several times I noticed through tunecu that while the water temperature rises, the minimum does not come as per the table but always remains high. After maybe 6/7...
  16. RIII Forever

    Remove stock fuel limiter

    thank you very much Steel, so you say that it is only a question of refining the map well and you get those extra 10-12 HP, right? do you kindly pass me the map that Carpenter gave you that scored 167 hp? (available with tune ecu, I would like to see the difference between mine and that)...
  17. RIII Forever

    Remove stock fuel limiter

    Wow but I can not explain this thing, there are several maps loaded on the forum with similar changes Carpenter and ramair that showed a result of 150/155 CV ...... how do you go so above? your data of 170 hp I think its still on the right wheel? for example at this link another value in line...
  18. RIII Forever

    Remove stock fuel limiter

    hello Ralsmith, thanks for the reply ..... I believe that the guy had already done the mapping, the first graphic is very "clean" like lines ..... I understood that it is really a modification in addition to a part of the fuel ..... or have I misunderstood? if I misunderstood .... how is it...
  19. RIII Forever

    Remove stock fuel limiter

    Hello everyone, I saw a post on Facebook a few days ago where the changed exhaust was downloaded (complete with header) by putting one of the CES Exhaust and the final result was about 153 hp. After that the fuel limit was removed, obtaining an extra 20 hp getting 170 hp! Anyone know how to...
  20. RIII Forever

    Idle is over 2700 rpm Help

    I loosened those on the handle, however I still have problems, the minimum is 1200 rpm high and it takes a few seconds and accelerator strokes to bring it down to normal values. Tunecu shows me values under the anomalous accelerator field 65486 ..... I turn it off and normalize it to 220 or...
Back
Top