Search results for query: *

  • Users: ant
  • Order by date
  1. ant

    Oberon slave cylinder used in the TTS kits

    Thought i would post the drawing that Oberon sent to me with the seal kit. Thanks for the link if they worked for you then i will ordered a set. Thanks for your help.
  2. ant

    Oberon slave cylinder used in the TTS kits

    Hi Art, Thanks for your reply. Oberon sent the new replacement seal kit out to me on 04/02/2020 so they would have been fully aware of your issue. At the time they said it was unusual for the slave cylinder to have an issues so check for burrs in the casing as these could damage the o rings...
  3. ant

    Oberon slave cylinder used in the TTS kits

    Thanks for you reply Art. Strangely Oberon are still saying that they are unaware of the issue. They did however say that they would look for alternative O rings. I have told them of the issues here on the forum and your finding the EPDM version O rings. Ant
  4. ant

    Oberon slave cylinder used in the TTS kits

    Having clutch problems with a leaking slave cylinder. Looks to me like a O ring has failed. I know most of us with the Oberon Buell 1125 slave cylinder used on TTS supercharger kits have had a few problems. The latest problem for me was i noticed a lost of clutch fluid. On further investigation...
  5. ant

    Hello From USA

    Hello and welcome from a hot and sticky UK..:)
  6. ant

    Carpenter baffle?

    No i didn't use any wrap but like you say that would help... I don't have any rattling noise and the one fixing screw was enough.. To be honest it's takes a while to fit.....Cut a little at a time until you get a snug fit..
  7. ant

    Carpenter baffle?

    In the photo the top baffle is from Carpenter...The other is the Samson.. The Samson fits inside the exhaust around 4 or 5 inches..As you can see in the photo most of the cone has been removed.. Hope this helps you..
  8. ant

    Carpenter baffle?

    Yes you would need to trim the cone...No there are no instruction supplied.. I will take some photos later today if that will help..
  9. ant

    Carpenter baffle?

    I fitted a Samson A161....It requires cutting a little off the end as it's too long.. The carpenter baffle just didn't look right.
  10. ant

    New Bike...Just Down!

    Glad to hear you are on the mend...
  11. ant

    Hi all, new here

    Hello and welcome from down south....Looks a nice bike very low miles. If it was me i would go and check it and get a test ride...
  12. ant

    Nail In Front Tire!

    A few years ago when i was out riding my Aprilia Tuono 1000 i had puncture in the rear tyre.... It's just unbelievable what i pulled from the tyre...NO it wasn't the pen.
  13. ant

    Fork legs are pitted....Poor chrome ?

    So i have noticed that the lower part of the fork tubes are slightly pitted..It's only on the very lower part and is about 1 inch or so up from the casting. But it's only going to get worse. The plan is to get the tubes re-chromed and get the top tube and the lower casting powder coated...
  14. ant

    Hi from Basingstoke

    Hello and welcome...:)
  15. ant

    Transmission shafts circlips: correct orientation of ?

    Yes that's the plan to change both the bearings...Also doing the second gear and timing chain guides etc.
  16. ant

    Transmission shafts circlips: correct orientation of ?

    I am in the process of installing the engine update kit..I did start a thread asking for advice on the torsional damper bearing and luckily R-III-R Turbo replied with some great photos covering the replacement of the bearings..The bearing didn't feel too bad until i cleaned them with petrol.
  17. ant

    Transmission shafts circlips: correct orientation of ?

    Hi Martin,Yes i was there on that ride and my brother came along too...It was great to put faces to names.. Hopefully we can all do another ride out in the near future.. My rocket is a 2007 and never had the update kit fitted..The original large bearing was open both sides now the updated...
  18. ant

    Transmission shafts circlips: correct orientation of ?

    Hi Martin,No problem mate.. I am doing the update kit on my 2007...Doing the torsional damper bearings at the moment... The bearing was installed the wrong way around...Caught them before they did any damage.. Hope your rebuild is going ok..
  19. ant

    How to remove the torsional damper bearings..

    Thanks again really helpful photos...Looking at the photo with the 2mm gap between the bearing and shoulder i should be able to remove the bearing without it flying off.. Looking at your photos when you pressed on the new bearing it stayed there allowing you to fit the clips..
  20. ant

    How to remove the torsional damper bearings..

    Thank you for your reply...The manual that i have for some reason doesn't have this section.....Maybe i need to find this copy. I did find a video on youtube with a guy removing the clips and the parts flying off..The problem might be getting the new bearing on because of the spring tension...
Back
Top