Search results for query: *

  1. JaR3d85

    Wanting confirmation... Rear wheel ticking...

    Absolutely, I have new wheel bearings on the way, the guy who had the bike before me had overfilled the break reservoirs, the oil and the final drive... When I last had the wheel off about 1k miles ago there was gear oil on the axle and some leaking from the opening on the bottom the the final...
  2. JaR3d85

    Wanting confirmation... Rear wheel ticking...

    Just want to confirm that I'm correct in assuming my rear wheel clicking when rolling is most likely the wheel bearings, happens backwards and forwards it takes a second for it to click rolling backwards after rolling forward assuming bearings are taking a second to catch again goimg the...
  3. JaR3d85

    After market mirrors

    I actually just purchased some 2010 triumph thunderbird mirrors, they sit quite a bit lower than the Mickey mouse ears on my 2014 roadster they are by no means smaller on the mirror but I think they will look a lot better . I attached a pic just for reference on what style. They are about half...
  4. JaR3d85

    Looking for some visual confirmation

    Thank you turbo! I took it for a spin the wheels that were on before were 7 year old avom cobra chromes, these metzlers feel way different, I will be able to give them a fair crack after I break them in a bit more .
  5. JaR3d85

    Looking for some visual confirmation

    I just had new tires put on, I also did some lube maintenance, and want to know if anyone can give me a confirmation that this looks correct and that my wheel is mated correctly to the final drive. I should have taken a before picture for reference but I was in a hurry this morning and didn't...
  6. JaR3d85

    2005 ignition switch removal

    I appreciate the response, have you done this before or know the procedure by chance? I am just curious if there is any special tool I might need to get before I tear into it, I ordered a new mount for the cast ignition housing I might have been able to bend it back but it's such a tight fit in...
  7. JaR3d85

    2005 ignition switch removal

    I know this is a old post, I have a bit of an issue, the dickhead that owned this bike before me had knocked it over with the steering lock engaged and it snapped the cast ignition housing and bent the mounts for the ignition... I'd like to find a new ignition my question is most ignitions just...
  8. JaR3d85

    Cannot locate a windshield fitting kit.

    So this is the windshield I purchased! I like that it doesn't look as wide or as tall as every other one out there. The thing I find strange is I have yet to find a single image of this exact windshield on a rocket 3! It pretty crazy to think that either people didn't like them or they are just...
  9. JaR3d85

    Cannot locate a windshield fitting kit.

    I tried them, the drop down wouldn't allow me to select USA to ship too... 🫤 And I appreciate your input I got a set ordered off eBay, thank you! 👍a little pricey but it is what it is. now I don't have to worry about custom fabrication, I could have made some billet ones at my work but in all...
  10. JaR3d85

    Cannot locate a windshield fitting kit.

    Trying to figure out a work around for installing a Roadster windshield I found on eBay, doesn't have the mounting kit just the windshield and it's brackets... I have been surfing Amazon looking for some hardware Iay have something nailed down... Well currently it's what I think may work but if...
  11. JaR3d85

    For Sale SOLD---Carpenter sidewinder exhaust--- SOLD

    I have a 04 to 19 rocket 3 sidewinder exhaust I just recently acquired and I have decided to go a different route as it is going to be a hassle to find someone close enough to tune the bike .. my loss your gain. There is one defect... That was my bad I dropped one on the ground and it left a...
  12. JaR3d85

    Installed sidewinder and ram air and hans0 +10 tune... Need input

    M tech motorcycles! I have no personal experience other than exchanged emails and them confirming the could tune it on a dyno and they are familiar with the tune ecu software but he did confirm it wouldn't be an issue, I also spoke too Erik carpenter today and he said he would try to find a map...
  13. JaR3d85

    Installed sidewinder and ram air and hans0 +10 tune... Need input

    I took it on a 10 mile ride just normal and something is really not right with it... Lots of loud decel popping, rolling on to throttle is not smooth at all , doesn't seem as though it pulls like when it was stock, first cold start the idle jumps from 900 up to 1300 or 1400, at a stop the idle...
  14. JaR3d85

    Installed sidewinder and ram air and hans0 +10 tune... Need input

    Alright, I guess then that's where I'm going to start, I appreciate your help. I'm gonna wait for the roads to dry up a bit today and then I will take it for a rip after I reflash this thing. Worst case I guess I will be swapping back to the factory system until I can get a baffle and a trip to...
  15. JaR3d85

    Installed sidewinder and ram air and hans0 +10 tune... Need input

    So are you saying I should be able to reload the map and it will have those adaptations already logged?
  16. JaR3d85

    Installed sidewinder and ram air and hans0 +10 tune... Need input

    ****, everything I had read said a bunch on different things... 🫤 Makes me wonder if I should swap the factory pipes back one and ride it for a bit and then switch back to the carpenters? I don't know what the fix from here would be? Will it eventually figure itself out? You all have a...
  17. JaR3d85

    Installed sidewinder and ram air and hans0 +10 tune... Need input

    I appreciate the reply, alright do you think with the new flow the throttle bodies could very well be out of sync? I have never messaged with this software or anything very technical on a R3 but if I can get a reading with the software And I can accurately tune them with a screw driver I don't...
  18. JaR3d85

    Installed sidewinder and ram air and hans0 +10 tune... Need input

    That was the only map/flash I saw that someone had commented they had the same setup as me and running it, there is another one that is the same almost just not plus 10? I should really take it to have it tuned but I don't have an truck so my plan was to ride it in to get it tuned but I just...
  19. JaR3d85

    Installed sidewinder and ram air and hans0 +10 tune... Need input

    Ok, so maps loaded exhaust and ram air installed, reset adaptations and 12 min tune, not sure but it seems like maybe it's hunting at idle? It definitely shakes a bit more and it's loud as **** aside from that I just want to see if anyone else has any experience with these upgrades and if they...
  20. JaR3d85

    Building a custom baffle need some insight/input.

    Alright so here it goes, just got my carpenter sidewinder and I know it's going to be loud. I don't care about my neighbors simply because they don't care about being dicks. Anyways, so I have a 2.25 perforated core 20 inch long I didn't realize that the 02 sensor location would prohibit my...
Back
Top