Recent content by eka

  1. eka

    Video on greasing the drive shaft splines.

    I wonder does it really need to take off pegs and starter motor cover. Could it be done without that extra job? Edit: Ah, there is that one bolt through cover and plastic.
  2. eka

    2025 Quick Shifter Install Problem

    The bike also has to be driven for awhile to get it relearn gears after installation.
  3. eka

    Wilbers competition 643 Install

    The height adjustment is at top end. You have to ask for it at order. I have it adjusted as long as possible. The screw itself adjust maybe that +/- 5mm, but as in swingarm the fixing point is much closer to swingarm fixing point, it moves maybe that +/- 15 mm at wheel end. I wanted suspension...
  4. eka

    Wilbers competition 643 Install

    I ordered with 15mm height adjustment and after about 20 000km the preload hose broke. I think it was a bit too short for that and stressed too much. They made me a bit longer hose in factory. I also have 100Nm spring insteadt of original 80Nm. They can also adjust manually preload area for...
  5. eka

    Eka's Pretty TuneEcu Maps

    AI says: Of course more you take out, the more you stress the engine, but isn't it just the point to tune anyway. I had 20 years ago turbo bike and couldn't stop tuning it until valve spring top cap separated and got wedged between the camshaft and the engine head and the camshaft snapped...
  6. eka

    Eka's Pretty TuneEcu Maps

    I have not had this bike at dyno to adjust perfect fuelling, but i assume my maps are pretty much on rich side. Penner tune is also richer than original map for optimum power, so i bet it won't get too lean. At least safer than original map for your bike. As my experimental maps have more...
  7. eka

    Eka's Pretty TuneEcu Maps

    I have crossed it to detonate few times in certain areas when trying to find the limits, but right away backed up few degrees. At least my bike doesn't detonate now in these values. I made spreadsheet about difference between my experiment and the original map: As you can see there is not so...
  8. eka

    Asymmetrical front tire wear

    I think all my bikes has worn tires more at right side...not just Rocket with wonky geometry and longitudinal engine. At right side traffic if you stay at yours side, the corners are tighter to right as you are at inner circle and left turns are at outer circle.
  9. eka

    Eka's Pretty TuneEcu Maps

    I forgot to say that center cylinder runs hottest, rear one a bit colder and front one coldest. I made spreadsheet and tested a bit. I have termal camera in my phone. Of course it's not super accurate way to do it and there is two layers of metal in headers, but looks like the best result is...
  10. eka

    Eka's Pretty TuneEcu Maps

    And of course there is more fuel where is more advance. Tuned fuelling for original ignition map: My iterated pretty fuelling map:
  11. eka

    Eka's Pretty TuneEcu Maps

    Yes, in higher load advance should be less. I iterated different angles and caps and this map was the best i found. At lower revs it should drop more or it starts pinging when open throttle. But if you look original map, it looks crazy hassling and that 22 degree advance doesn't make sense...
  12. eka

    2022 Triumph Rocket3 Gt

    I am couple kgs heavier and measured that rear suspension sacks a bit over 4 cm when preload is fully tightened. It is too much. Generally it should sack like 1/3 of spring travel. There was only like 6 cm spring travel left with all preload. I suggest you put full preload, rebound fully open...
  13. eka

    Eka's Pretty TuneEcu Maps

    I have a bad habit to reprogram ECU all the time and try this and that. I just noticed, that i have reprogrammed ECU over 100 times and was like wtf. Better stop and maybe i share what i have done, so you don't have to be dork like me. Anyways, original ignition map sucks. Values goes here and...
  14. eka

    Customised seat myself

    I did like original R seat. Never got sore butt, but my knees were a bit stiff after long rides. I have aftermarket pegs higher than original and it also makes knee angle a bit tighter. I can't lower pegs as still scratching them. Anyways the seat is couple centimerers higher and wider. Little...
  15. eka

    2022 GT Grip Question

See more
Back
Top