Recent content by Bedifferent

  1. Bedifferent

    Madstad windscreen 2020-2024 R3GT

    Thanks for the info on the windscreen. I'm running the Madstad 24" and it seems to work okay, but I wish it was styled just a little wider. I don't know if you checked out the post on the lowers that I made. Every little bit helps, but I don't want to muck up the appearance of my bike. There...
  2. Bedifferent

    Rocket wont start ???

    Good plan..I have a little device/tester that shows the draw down voltage when starting. It uses LEDs and the lowest voltage LED stays lit to show the voltage. It shouldn't go below 9 volts when cranking according to my tester. If it does, things are questionable.
  3. Bedifferent

    Change your crush washers

    Always use new crush washers! Why cut corners for things that cheap. You can buy them on Amazon and they work fine. They are not quite as thick as the Triump aluminum stock washers, but they still crush and seal just fine. I have both aluminum and copper. I used copper on the final drive...
  4. Bedifferent

    Rocket wont start ???

    OMG...5 years?!! Replace it! Mines goes to recycling after 2-3 just on principle. Some people disagree, but it's just sickening in when it won't start and it boils down to the battery. My batteries are always on a maintainer if they are going to be setting for more than a few days. I don't...
  5. Bedifferent

    Rocket wont start ???

    I would not assume the battery is ok. I've read about a lot of starting issues on the forum down through the years and 90% of the time it comes down to the battery or the connections. The lights may look good, but it's the ECU not having enough voltage. They are fussy!
  6. Bedifferent

    Question about Noise while releasing clutch

    I agree, no issues from what I've noticed. I always use Triumph oil in my newer GT. I use to use Castrol 4T in my R3T, but the dealer said not. Since it is still under warranty, I don't have an issue with that. I worry about friction modifiers as well with different oils. With all that...
  7. Bedifferent

    Lowers for my GT...My latest project

    Wow...those babies are super sized. Good job though! There is always the battle between form and function and if it works for you I say...go for it. If I wasn't focused on form I would probably make mine bigger, but I think there may be a point of diminishing return as well. I only have...
  8. Bedifferent

    Lowers for my GT...My latest project

    I considered that, but I would be half way home if I just cut the plastic. Having made bigger lowers and windshield wind deflectors for my 2015 R3T, I was pretty sure I knew what size and design I wanted to make things look good. I think I'm there without mucking up the looks of my bike. :oops::D
  9. Bedifferent

    Lowers for my GT...My latest project

    I looked at those. Sadly, the size just isn't going to cut it when it come to going around the fork tubes. 58mm is what I measured the tubes at and that translates to 2.28346 inches. I couldn't make the first 58mm clamps that I bought work on the tubes without serious modifications and the...
  10. Bedifferent

    Lowers for my GT...My latest project

    Yes, I have taken them out for a test ride. I do believe they make a difference, but it is always hard to tell just how much without taking them off and on to test. My slightly larger version should be the best test. It's a bit cool today and not t-shirt weather, so I cannot speak...
  11. Bedifferent

    Lowers for my GT...My latest project

    I thought I would do a fresh post with the lowers mounted. As I've mentioned before, I cut these lower out of some of the plastic I had on hand and the plastic was not big enough to cut them full length and size. They will be an inch longer and the cutaways for the turn signals will be smaller...
  12. Bedifferent

    Lowers for my GT...My latest project

    I understand...there's always the snail mail option if you change your mind. You would have to PM me with an address. Personally, I don't know if I would go much beyond 9 inches tall as thing might start getting ugly looking beyond that. 🤣
  13. Bedifferent

    Lowers for my GT...My latest project

    I have created two really nice templates that I would be happy to share. One is the size of what I currently posted and the other is about a inch longer. I plan to have the longer ones custom cut from a pdf file which is what the company uses to laser cut the plastic. It is around 9 inches...
  14. Bedifferent

    Lowers for my GT...My latest project

    I'll post more info when I'm done. They seem to be helping with the wind coming up around under the handlebar around the tank. I took the paper off and they really look nice. They blend in well.
  15. Bedifferent

    Lowers for my GT...My latest project

    Looks good. It's never an easy job on doing homemade modifications. The Powerbronze hand guards work well for air flow over the tops of your hands. With my setup, I notice most of the airflow coming up from underneath the bars. I don't expect miracles, but any reduction would be nice.
See more
Back
Top