Search results for query: *

  1. warp9.9

    Gearbox repair?

    Some people switch/reverse the shift pattern because they think it's faster race shifting especially without using the clutch. Does seem that way, but it is harder on the transmission. Especially hard on shift forks and easier to pop circlips out of their grooves.
  2. warp9.9

    MAP and or Air Pressure sensor fault

    Did you get the stepper motor with it ? If so when you are done getting her sorted out you might end up putting it back on the bike so it runs right and you can perform proper maintenance . Like a full ISCV reset. The simple 12 minute time operation to sync the ECU with the engine sensors.
  3. warp9.9

    Dreaded high idle problem

    Yeppers my 06 had the Old TPS back when it just started to be a problem. After the change I never had a broblem unless you don't keep all the throttle body linkages and stepper motor linkage clean. So the throttle return is alwas the same. Especially when you turn the key and the process of ecm...
  4. warp9.9

    Header exhaust leak

    Ya you could use a little rotation of #2 header tube. Remember each tube slides into the merge collector where the lower springs are. Other then being annoyed with it. It won't hurt your bike.
  5. warp9.9

    Header exhaust leak

    Yep T bolt pipe clamps will work you just cant see mine with the cust heat shields from these pictures. But they are there if ya make sure the T bolt is on the underside the rest is a nice matching band of stainless so it doesn't look perker would luke a dark sider :D
  6. warp9.9

    Southern ride this Spring?

    I'm watching this hoping I got time to take a break and relax !!!
  7. warp9.9

    Header exhaust leak

    Same carpenter header. With just some straight aftermarket heat shields this is Gracie I first adapted the Harley baffle cone to the Carpenter headers. Its beer thirty ;)
  8. warp9.9

    Header exhaust leak

    Its hard to blow ot up but I drilled holes in the shield for the springs that hold the header pipes to aluminum manifold. There are stainless hose clamp under the shields.
  9. warp9.9

    Header exhaust leak

    Dude calm down :) there is no heat sheild for the Carpenter header except for the few custom built ones from Australia. Of them few I own two sets. Heck it took years for them to develop a baffle for the end of the megaphone. Thats why people go different routes. Whilst doing my fire clean up I...
  10. warp9.9

    Header exhaust leak

    The header flange/manifold is made of aluminum. Bob Carpenter set it up like that kind of like sport bike with stainless steel springs as retainers. The stainless header runners just slip over the custum header flange/manifold. When I get back to Illinois I'll look at the 3 sets I have to see...
  11. warp9.9

    Header exhaust leak

    I didn't like that on mine either. Even though they never came off I added the T style clamps and never looked back. They are stainless steel to so they don't rust !!! Hope this helps Lupe !!!!
  12. warp9.9

    Carpenter owners, help

    Rev limiter is set at 9k on Carpenter Rockets.
  13. warp9.9

    R3T Floorboards Have To Go!

    Jim you can bolt any of the floor board rails from the touring or classic to the O5. I'm not sure but the accessories floor boards triumph made fit on the standard rails. They are at a steeper angle the the classic or touring floor boards. I haven't been home in a month but I'll look at the...
  14. warp9.9

    Is it Fast?

    Cardiomyopathy but I am watching for aftermarket parts ;)
  15. warp9.9

    Florida captains

    I've been in contact with Tripp's he's fine a little rain not much wind. I see Ogre was out riding the grom today and posting on farcebook.
  16. warp9.9

    Is it Fast?

    Its alright so you've never been blown :D
  17. warp9.9

    RAA Fall Fling Maggie Valley

    Ya he's fine not much damage electrical wasn't out long but he has a generator anyway.
  18. warp9.9

    How FAST ???

    Slow :D
  19. warp9.9

    RAA Fall Fling Maggie Valley

    When I used to drink there was only two kinds. The stuff I bought and the stuff I was given. And they were both pretty darn good :D
  20. warp9.9

    Valve noise below 1700 RPM, what can cause this?

    In my opinion the only to change the tensioner while keeping tension and timing would be to go down thru the top of the cam cover in the front. This way you could hold pressure on the cam chain tensioner of the guide. Using the arch of the guide against the chain so it keeps the chain tight on...
Back
Top