Search results for query: *

  1. TURBO200R4

    Rocket 3 GT Cruise Control

    Then walk around the bike and say three hale marys
  2. TURBO200R4

    Gear position sensor 2014 roadster

    Not my link poster idk did all that work. and all of us apprecate those links
  3. TURBO200R4

    Gear position sensor 2014 roadster

    https://www.r3owners.net/threads/10mm-socket.49707/ i will post and then try go to this thread and then in #1 post poster IDK then click on lots of rocket stuff-worth reading! then click on r3r electrical 1 or r3r electrical 2
  4. TURBO200R4

    Gear position sensor 2014 roadster

    what year is the r3? is it roadster or touring? hth
  5. TURBO200R4

    30 Amp Fuse Keeps blowing out

    I don't neccessarly agree but the more info the better it is to check just thinking that the brake lights might go through that main #11 30 amp fuse and if they were grounded out might give you the problem. Have seen car tires that ripped the wires under the fender.
  6. TURBO200R4

    30 Amp Fuse Keeps blowing out

    That is correct we are trying to narrow down the area/circuits where the problem is. when some people change the headlights sometimes there is not a place to put the parking light so they remove the bulb and then sooner or later the two terminals get together and creates a short to ground and...
  7. TURBO200R4

    30 Amp Fuse Keeps blowing out

    it sounds like you have a direct short. if it was my bike i would buy a breaker fuse 30 amp so you don't go through a lot of fuses. now i would make sure that you have a diagram of the fuses so that you know which ones to put where they belong. pull all the fuses then replsce the 30 amp with the...
  8. TURBO200R4

    Starter upgrade issues

    I said it b4 and i will say it again if the starter solenoid is clicking then all the safetys are working along with the relay. So either you're not getting enough voltage at the starter solenoid (Witch i dought) or you have a starter problem. I would recommend another starter solenoid or if...
  9. TURBO200R4

    Starter upgrade issues

    as long as you have 10 volts that starter should turn over now if you check it with it hooked up and it remains the same then something is wrong with the starter if it drops a little (one volt ?) then you are energizing the solenoid but it is not making the conection to the starter. the voltage...
  10. TURBO200R4

    Hanging Idle

    i would think that it may be sticking where the two cables meet at the throttle shaft. there is a spring there that needs to be lubed. that little spring area there is a system where you can hold the throttle closed as hard as you want and push on the little part and it will rev to 5000 rpm...
  11. TURBO200R4

    05 rocket 3 tune

    Thing you need to do is copy and save your old tune some of these tunes are not as good as what you are running some of the tunes are set up to drop your mileage to 20 per gal:thumbsdown:
  12. TURBO200R4

    05 rocket 3 tune

    we now return to normal programing lol
  13. TURBO200R4

    05 rocket 3 tune

    Why risk a screw in the motor when you can type 100 in the tuneecu? i have never done the 12 minute and probably never will it is just a waste of time and gas.
  14. TURBO200R4

    05 rocket 3 tune

    the tune ecu will open the secondarys to 100% android lap top with lontech cable android phone with lx/mx dongle the 12 minute is for idle set after you disconect the battery hth
  15. TURBO200R4

    Starter upgrade issues

    Good on finding the bad ground wire However that starter will crank at 10 volts and i seen one crank at 9.4volts. So your thinking is a little off. I would guess that the volts/amps is not getting to the starter you probably still need some trouble shooting. Kevin is correct try jumping it...
  16. TURBO200R4

    Starter upgrade issues

    The ignition switch has a habit of going bad because the headlights run through it that is the reason i put my lights on relays. Sometimes the white/blue wire just melts the soddet and it fals off. Other times it just melts the switch. Did you get the simple gard dawg or the one that has a...
  17. TURBO200R4

    Starter upgrade issues

    It has been a long time since i wired mine that way so i forgot that i had put my lights on relays. So what I told you is only for checking purpose. Because the lights will run down the battery.
  18. TURBO200R4

    Starter upgrade issues

    Congratulations i think that you have checked everything except what you should have checked. Now you have posted enough info form to tell you what is wrong. Your positive wire going to relay terminal number 30 does not have 12 volts so the lights/starter will not work. Being that i don't...
  19. TURBO200R4

    Petrol gauge dilemma

    I think that most of the gauge lights goes off at about half full/empty you would have to bend the float rod and it is pretty easy to screw it up.
  20. TURBO200R4

    Starter upgrade issues

    I will see if i can help you have saftys clutch switch,nuetral,kick stand switch when all these saftys have been met then the ecu will send the signal to the starter relay so the starter relay will entergize up to that point you are working good👍 now with the starter relay entergized the current...
Back
Top