Search results for query: *

  1. oteczdmitriy

    Ignition problem- Rocket III (2004)

    lift the fuel tank, a large connector to the ignition switch, the white and blue wire burned out, move it to start it, solder it so as not to remember
  2. oteczdmitriy

    2011 Roadster Viking 3-1 Ramair Popping

    https://www.r3owners.net/resources/2011-2011-r3r-tors-ramair-with-more-fuel-and-less-timing-in-cruise-decel-pop-added.36/
  3. oteczdmitriy

    How much fork oil do each fork hold

    666
  4. oteczdmitriy

    Resource Download 2011 2011 R3R Tors Ramair with more fuel and less timing in cruise, decel pop added

    This is the best map available, especially when there is no tuner around. Fourth year with me, Ramair and various homemade exhausts, no pops. Thanks to John and Martin.
  5. oteczdmitriy

    Sai test in tune ECU ghosted

    Secondary air injection, not on the R3, the last time I used this feature was the Triumph Speedmaster, and then removed the popping system physically.
  6. oteczdmitriy

    Anyone run a Carpenter sidewinder in a 3-1-2 configuration?

    I mean, the design of the headers, I think the last one with TORs, is more than successful, not a single pants was damaged, next winter I will make one of 304 stainless steel, and ceramic coating
  7. oteczdmitriy

    10w40 or 15w50?

    I got cheap Motul 7100 10W60 oil, it is not recommended for use. Firstly: strong engine vibration (it didn’t seem to me). Secondly: it’s not possible to determine the oil level (remains on the engine walls). Thirdly: the oil pressure indicator has stopped glowing. After driving a one hundred...
  8. oteczdmitriy

    Anyone run a Carpenter sidewinder in a 3-1-2 configuration?

    I'm looking for the right solution for headers, AISI 201 stainless steel, darkens a lot when heated.
  9. oteczdmitriy

    Anyone run a Carpenter sidewinder in a 3-1-2 configuration?

    If you remove the gasket, in diagram No. 23, it is possible to install link pipe No. 13 increased to 45 mm (38 mm in stock). It remains to make a bypass pipe with a pedestrian on the Carpenter headers. Of course, the installation only makes sense with TORs. So it happened to me, bypass pipe 60...
  10. Another winter gone, now with TORs

    Another winter gone, now with TORs

    exhaust
  11. IMG_20220417_125550.jpg

    IMG_20220417_125550.jpg

    • oteczdmitriy
    • Media item
    • Comments: 0
    • Album: Another winter gone, now with TORs
  12. IMG_20220417_125609.jpg

    IMG_20220417_125609.jpg

    • oteczdmitriy
    • Media item
    • Comments: 0
    • Album: Another winter gone, now with TORs
  13. IMG_20220417_125622.jpg

    IMG_20220417_125622.jpg

    • oteczdmitriy
    • Media item
    • Comments: 0
    • Album: Another winter gone, now with TORs
  14. IMG_20220417_125637.jpg

    IMG_20220417_125637.jpg

    • oteczdmitriy
    • Media item
    • Comments: 0
    • Album: Another winter gone, now with TORs
  15. oteczdmitriy

    Remove Rear Shocks Advice? R3 Roadster 2018

    you don't need to remove the shock absorber to remove the trim (bumper?)
  16. oteczdmitriy

    Remove Rear Shocks Advice? R3 Roadster 2018

    lifting the wheel off the ground, remove the shock absorber without problems, and yes, remove one at a time
  17. oteczdmitriy

    Neutral issue - Gear position sensor (GPS)

    The part is assembled without a washer, there are no difficulties in installing it back
  18. oteczdmitriy

    Neutral issue - Gear position sensor (GPS)

    Gear position sensor GPS Gear position sensor GPS
  19. oteczdmitriy

    How To: Replace Gear Position Sensor (GPS)

    For three wire
  20. oteczdmitriy

    How To: Replace Gear Position Sensor (GPS)

    Gear position sensor GPS
Back
Top