Search results

  1. sleeves

    Mother of Rocket III sighted!

    Nice drum brakes for slowing this down
  2. sleeves

    centre stand

    Sorry no installation manual. Took some pics tho.
  3. sleeves

    centre stand

    Gday. I will have a look tomorrow as may have fitting instructions. i have one of these and its great. Wont fit ABS bikes and you need to drill and retap a lug on bottom of frame to be able to mount it
  4. sleeves

    I know I'm a sign nut.

    Or If you generally don't like swing bridges, oh how my wife laughs at me.
  5. sleeves

    I know I'm a sign nut.

    Yep, after Cave Creek. I guess...
  6. sleeves

    I know I'm a sign nut.

  7. sleeves

    Aftermarket Cables

    Barnett is good quality. I used a local industrial cable maker for mine. Had to send him throttle cable for the small parts but clutch ge had everything. Hel brake lines and plenty of wiring extension soldering.
  8. sleeves

    Rear wheel bearings -- RESOLVED! Thanks for all the advice.

    With my old bikes i often warm the hubs with heat gun and freeze the bearings they drop in and expand. If worn use Loctite but its a hassle for the next replacement. Often try freeze spray for removal too. Loosened swingarm nuts like this recently
  9. sleeves

    Help with TuneECU reading map from 2014 Roadster

    Sorry can ignore just read the above posts.:banghead:
  10. sleeves

    Help with TuneECU reading map from 2014 Roadster

    Hey just a note with the Roadsters I think there are two different ECU's. They changed them at some point in the VIN numbers and the MAP's are not interchangeable between the two. PIA.
  11. sleeves

    extension for passenger footpeg

    I have these they lower and move the pegs forward that helps no end. Needed some garage fabrication to make work. Easy to make from scratch too if need be.
  12. sleeves

    baffles in paul bryant exhaust with headers?

    Also the SS steelo pad stuff we put in helped and was better than fibreglass but did pack up one end still. Wont blow out though.
  13. sleeves

    baffles in paul bryant exhaust with headers?

    Hi Hoopla I got had the same issue after running with the header and single pipe for an 850km (520miles) run one day it was pretty droning and annoying. I got Paul to weld in a perforated baffle half way down the tube, this helped massively. Also I changed my helmet to a Shoei GT Air, this is...
  14. sleeves

    2005 STALLING, NO ECM DATA WHEN RUNNING. UPDATED

    Gday I haven't been posting for a while on the forum but I have two 05 R3's and I'm pretty certain the wiring doesn't get hot on the charging circuit. I am wondering if either the regulator is not operating correctly? maybe not dumping excess current, the stock regulator/rectifier dumps the...
  15. sleeves

    ECM and stuff (sorta) explained.....

    Been running map based fuel mapping successfully for last couple of years using PCV.
  16. sleeves

    Triumph is in trouble

    A mate has a couple of these German Triumphs he took one on a rally and I can assure you its not a performer.
  17. sleeves

    Aftermarket exhaust

    Thank you been offline. Adding fuel on L table stops backfiring on old models. Think putting on dyno good idea but doubt tuners have tools or access to ECU to correct at this stage. Will happen though.
  18. sleeves

    Aftermarket exhaust

    Ah the old misunderstood and misrepresented 12 minute tune like the old R3s. This really is entirely dependent on whether the O2 sensor is wideband or narrow. Narrow ONLY works at idle. i.e no load. The old R3s were NB, maybe the new are WB? If NB, yes, you can let it idle and a narrow band...
  19. sleeves

    Clutch sensor problem

    Just had a look through the wiring diagram (was for an older model) but cannot see any hard wire link between the clutch switch and the fuel gauge accessory plug other than the earth. Also the clutch switch wires direct to the ECU so any issues are probably the ECU software. The bike looks at...
  20. sleeves

    Another TPS Question

    Just something to check on the mechanical side is the MAP sensor hoses just in case they have cracked.
Back
Top