Search results for query: *

  1. The service light came on (A little light shaped like a wrench). It stays on.

    Hi Tal I have done as you said in your forum but the spanner is still showing on the speedo I went into sevice display and it is due for that @15000kms but has only done 3000kms but is overdue by time Can you change the service date in settings All help very much appreciated Kind Regards Mark

  2. Removing right side exhaust caps?

    I had the same problem so i went to a machine shop and got 2 small bolts with the same theard so i could use an open ended spanner Worked real easy

  3. Side Stand

    Hi There I cut 8mm off my stand as the lean angle was to steep and my friends R3 fell over in the high wind I used a battery grinder with a 1mm cut off wheel Kind Regards Mark

  4. Good choice for crash bars for my 23 GT

    The little short piece is to take a 17mm /10mm drive socket so you dont have to take the airbox off It just fits in there and you need a 50 Torks for the right hand side Take care

  5. Side Stand

    Hi There 7 mm was what i cut off but if i had to do it again i would cut off 6 mm and i didnt make the foot any bigger and have had no problems .The bike sits alot better now and wont look like it is going to blow over .

  6. Side Stand

    Hi There I cut 7 mm off my side stand with a battery grinder with a 1mm cutting disc and it made quite a difference when parked I did this while the stand was on the bike and the bike was on a trolley jack Kind Regards Mark

  7. 23 plate rocket 3 whats this fault mean

    Hi There The service light comes on if the 12 months is up between services even if the miles are not many but you can go into setting and take it off

  8. Hi Folks. Need a picture of a 2020 & post R3 with a set of crash bars.

    there is no instructions but mine fitted ok Do the right hand side first by taking out the long bolt that goes though the frame The nut size on the left hand side is 17mm You do not have to put a jack under the motor as there is other bolts that hold the motor to the frame That is correct...

  9. Hi Folks. Need a picture of a 2020 & post R3 with a set of crash bars.

    Hi There There is photos of my R3 Gt with the fitted crash bars on page 2 of this forum The spanner with the square on one end is to take a 17mm socket with 10mm drive so you do not have to take the air box off The fitting on the right hand side is a Torx 50 You no not need to put a jack...

  10. Hi Folks. Need a picture of a 2020 & post R3 with a set of crash bars.

  11. Hi Folks. Need a picture of a 2020 & post R3 with a set of crash bars.

    Hi There The video has expired on my email and the little spanner thing is a 10mm drive for the 17mm socket There are photos of my crash bars fitted on the crash bar forum

  12. Hi Folks. Need a picture of a 2020 & post R3 with a set of crash bars.

    Hi There The piece you are referring to is to takes a 17mm socket to undo the frame nut on the left-hand side so you do not have to take the tank and airbox off to fix the bars I WILL TRY TO SEND YOU A VIDEO OF THE FITTING INSTICTIONS Kind Regards Mark

  13. the sissy bar for Rocket 3 GT

  14. the sissy bar for Rocket 3 GT

    Many thanks, everyone for your help I have had one made for my Triumph R 3 which is just perfect for my situation Will try to send a photo Ride Safe from New Zealand

  15. Penner maps

    Many Thanks from NZ

  16. Penner maps

    Yes i am in New Zealand

  17. Penner maps

    Hi There. I have 2021 model Triumph Rocket 3 GT VIN SMTYBG10J5MAC etc

  18. Penner maps

    Many thanks as i am out of my depth on this remapping procedure and all the reviews are so positive Kind Regards Mark

  19. Penner maps

    Hi Tal I like your comments on the remapping of your Triumph R 3 Is it a mission to do if you are not computer savy as i live in Napier NZ and do you know of anyone in the North Island that i could take my bike too Kind Regards Mark

  20. Go Da Fords!!!

    HI Tai I have a 2021 Rocket 3 GT in Napier and was looking at getting it mapped with a Penner tune Is this a mission as i have read you had it done and a very happy with the out come Many Thanks Mark
Back
Top