Search results for query: *

  • Users: bernard
  • Content: Threads
  • Order by date
  1. bernard

    For Sale 2014 Carpenter R3R & camper

    2014 R3R ABS. 71,000 miles. Runs great. Good tires & tread. Carpenter engine dynoed 230HP/170ftlbs on a 210HP kit. Running 89 octane. Carpenter stainless exhaust. Trans rebuilt by Robinson with billet 4th gear, backcut gears, upgraded retaining clips. Rivco risers. Rear Progressive...
  2. bernard

    Engine Issue

    2014 Roadster. It sounds OK at idle. Off idle to about 2500 rpm there is a distinct miss. It starts smoothing out at 3000 rpm and runs strong and smooth to redline. In addition to the miss, there is an extra noise coming from the exhaust pipe. The pipe is a 3 into 1 baffled megaphone...
  3. bernard

    Rear wheel bearings -- RESOLVED! Thanks for all the advice.

    I bought a nifty slide hammer expanding wheel bearing puller. Removed the seal and circlip from right side bearing and installed the nifty bearing puller. After banging it more than I ever did my girlfriends, the bearing didn't budge. After removing the cush drive cover, I tried the other...
  4. bernard

    Engine light was on

    2014 Rocket Roadster - Going down highway, bike's running good, engine light comes on, stays on. Headed home, only a few miles away. Bike still ran good at highway speed, but when I got off the highway, it started cutting out at slow speed like it wasn't getting enough fuel. A few hundred...
  5. bernard

    Quick LED upgrade

    During the 2020 West RAA, I noticed it was hard to see the rear turn signals on the older incandescent Rockets, especially in the day time. The new Rocket LED turn signals 'pop' and it's easy to tell if the rider is going to turn. So I decided to upgrade my 2014 R3R rear turn signals on the...
  6. bernard

    Part Location?

    I pulled the engine from my 2014 Rocket Roadster and just put it back in. I don't have any leftover bolts, but I have a part which needs to find a home. Recognize this?
  7. bernard

    Swing Arm Install - got it done!

    Pulled engine and now putting it together. I slipped the driveshaft into the bevel gear drive and turned shaft to verify it was engaged. Then I slid the swing arm back into original position while engaging the splines onto the engine output shaft. But it doesn't want to slide completely in...
  8. bernard

    Helpful Hint, Please!

    Pulling my engine. Everything disconnected, unbolted. But frame won't clear engine. Binding at right front mount arm. I know there's a trick to clearing the frame, but I haven't figured it out yet. Thanks.
  9. bernard

    Bonnie Bones says:

    "I like to ride hard."
  10. bernard

    Duh!

    I was looking for my engine number, but didn't find it. Where did they put the little bugger? Also I have a complete factory TORS exhaust off a 2014 R3R. Is there any interest in such an item?
  11. bernard

    Carpenterized Nov, 2019

    210HP kit pulled 230HP @ rear wheel. Thanks, Bob! You're the man! Thanks to Eddie and Erik, too!
  12. bernard

    Airbox removal/ breather access

    I need to put a filter on the crankcase breather, but I can't even get my hands in there. So I'm trying to remove the airbox for access. After unbolting, the manual says to "manoeuvre" the airbox out of the frame. I'm trying to pull it from the right side, but it's very stubborn. Especially...
  13. bernard

    going camping

  14. bernard

    Check out my bags

    $300 from ridebikegear. Quick release brackets. I lowered the TOR exhaust 3 inches at the rear tips. Reinforced bags with stainless sheet metal covering the inner side.
  15. bernard

    check out my new bags

    I'm new to this forum stuff and new to Triumph. I'm going to try and attach pics of my new bags w/LED lighting, turn signals, side light strip, and quick release brackets. . Hope it works.
  16. bernard

    New 2014 R3 Roadster dead in the water

    Picked up my net 2014 R3 Roadster yesterday Logged about 200 miles with a few stops. Then bike started and quit a couple of times. Then it wouldn't even crank, not even a 'click'. Full electric and gas. Bike was remapped by the dealer for TOR exhaust. Very disappointed and worried about...
Back
Top