Kuryaken ISO Grips 2014 R3T

Tank

Supercharged

Joined

Apr 9, 2014

Messages

343

• Oct 8, 2014

• #1

Hey lads;

Despite what cruisercustomizing.com says the 2014 R3T requires the ISO Grip 6236. Im not sure about the roadster or older models but the 2014 is throttle by wire and the ones recommended by cruisercustomizing.com (iso grips 6240) will not work.

Go figure...

 

Tank

Supercharged

Joined

Apr 9, 2014

Messages

343

• Oct 9, 2014

• #2

ISO grips are installed.

Another tip; if you don't want to glue the clutch grip into place.

I found that if you put three evenly spaced stripes of electrical tape on the handle bar and then carfully twist the iso grip back and forth until its in place you dont need to glue it.

 

Attachments

• 
  20141009_141215.jpg

  1.5 MB · Views: 0

Last edited: Oct 9, 2014

Tank

Supercharged

Joined

Apr 9, 2014

Messages

343

• Oct 9, 2014

• #3

Thanks to @neveragain for the idea to add the OEM end caps to the ISO grips.

 

Attachments

• 
  20141009_175453.jpg

  1.4 MB · Views: 0
• 
  20141009_175503.jpg

  1.4 MB · Views: 0

Dawg68

Nitrous

Joined

Apr 1, 2013

Messages

1,360

Location

Chilliwack B.C.

Ride

2014 R3R / 2017 R3T

• Oct 9, 2014

• #4

Looks good

 

cr0ft

Living Legend

Joined

Jun 28, 2012

Messages

2,406

Location

Finland

Ride

Triumph Rocket III Touring 2010

• Oct 19, 2014

• #5

Looks very good. And the ability to retain the bar-ends is great, it also opens up to getting a set of Barkbusters Blizzard hand guards for cold-weather riding, just put them on there when you need them and leave them off when you don't.

Except as soon as I start adding chrome grips I know I'll go nuts and buy the chrome brake grips, the chrome brake cylinder cover, the chrome switchcube housings... expensive Isos (or Avons) all in all. Oh well.

 

Dawg68

Nitrous

Joined

Apr 1, 2013

Messages

1,360

Location

Chilliwack B.C.

Ride

2014 R3R / 2017 R3T

• Oct 19, 2014

• #6

Does anyone have the ISO Grips on a 13/14 Roadster?which model did you buy?

 

Dawg68

Nitrous

Joined

Apr 1, 2013

Messages

1,360

Location

Chilliwack B.C.

Ride

2014 R3R / 2017 R3T

• Oct 30, 2014

• #7

I just ordered a set of ISO Grips, am I correct in that I will have to cut off the clutch side grip and the throttle grip will slide off?

 

Tank

Supercharged

Joined

Apr 9, 2014

Messages

343

• Oct 30, 2014

• #8

Dawg68 said:

I just ordered a set of ISO Grips, am I correct in that I will have to cut off the clutch side grip and the throttle grip will slide off?

Click to expand...

Brake side:
On my 2014 R3T i opened up the switch housing disconnect the throttle wire and it slide off.

Clutch side
I used a thinner long screw driver pryed the rubber grip up a little added a few scoots of Wd40. I turned the grip and off it slide.

No damage, no muss, no fuss.

 

Wrecka

Living Legend

Joined

Mar 19, 2006

Messages

3,161

Location

Pimpama

Ride

2013 R3R

• Oct 31, 2014

• #9

Dawg68 said:

I just ordered a set of ISO Grips, am I correct in that I will have to cut off the clutch side grip and the throttle grip will slide off?

Click to expand...

You dont have to cut the grip , i use my compressor and shoot a stream of compressed air under the grip as i wiggle it off

 

breeze

Living Legend

Joined

May 14, 2012

Messages

3,254

Location

bloomfield n.m.

Ride

07 classic/01legend/72 bonne

• Oct 31, 2014

• #10

Wrecka said:

You dont have to cut the grip , i use my compressor and shoot a stream of compressed air under the grip as i wiggle it off

Click to expand...

not sure they are talking about the same grips